Plumbing Basics: A Must for Bathtub Installation
Plumbing Basics: A Must for Bathtub Installation
Blog Article
They are making a few good points on the subject of A Step-by-Step Guide to Installing a Bathtub in general in this article on the next paragraphs.
Installing a bath tub isn't specifically rocket science, but it does call for solid plumbing, carpentry, as well as in some cases, tiling abilities. Changing an old bathtub with a brand-new one is also a reasonably hard task. If the old tub is readily accessible, the project can relocate rapidly; if you have to open up a wall to get rid of the old bathtub as well as position the brand-new bathtub, the task is a lot harder. In either situation, the project is within a residence handyman's skills, although you will certainly require an assistant to move out the old tub as well as set in the brand-new one. See to it you have actually certified on your own for the work and also fit trying it. As opposed to working with a professional to take over a halfway-completed project, it is better to consider using one prior to you begin. Chances are you may require an expert plumber to make tube connections.
This write-up will certainly assist you install a brand-new tub in your bathroom if you have actually already bought a brand-new tub as well as do not need to transform the setup of your previous water system pipes.
Your devices as well as material list must consist of the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water system. After doing so, activate the faucets to drain pipes any kind of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a cloth all set for the staying water that will originate from the pipes. As soon as the supply pipes have been eliminated, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Before proceeding to fit the brand-new taps, contrast the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the thread. One end of the port fits on the plastic tail of the tap and the various other end provides a link to the existing supply pipes.
If you require to fit a monobloc, after that you will require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the mounting opening in the bath/basin making certain that the washers remain in place in between the tap and also the sink. Safeguard the tap in position with the maker supplied backnut. Once the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The former type must be connected to the tap ends first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Mounting the Tub
Using the two wood boards under its feet, put the bath tub in the required placement. The wooden boards are handy in evenly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four little factors.
The following goal is to guarantee that the tub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet port to the suitable supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Activate the water system as well as check all joints and new pipework for leakages and also tighten them if necessary. Fill up the tub as well as additionally check the overflow outlet and the normal electrical outlet for leakages.
Finally, deal with the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the tub should wait up until the bath tub has been made use of at least when as this will certainly settle it into its last position.
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to make sure that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to avoid stress on the tub.
Fit the versatile tap adapters to the bottom of both faucets making use of 2 nuts and olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Link the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its final placement.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate sufficient to break a rigid seal, creating the water to permeate the wall in between the bath and also the tiling, causing difficulties with wetness as well as possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and fittings. They are marketed in tubes and cartridges, and are capable of sealing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water prior to securing, to permit the movement experienced when the tub is in use. The sealer can crack fairly early if you do not consider this motion before sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Do you enjoy more info about A Step-by-Step Guide to Installing a Bathtub? Try leaving a remark down the page. We will be glad to listen to your views about this review. In hopes to see you back again before long. Sharing is nice. Helping people is fun. Many thanks for your time. Visit again soon.
Find Out More Report this page